What winter projects are you planning for your Beast?

[ghlkal]

Originally Posted by GOLDCYLON

7. Upgrade front J55 calipers to 96 GS calipers and probably front pads

I'd like to do this also, but I have a hard time finding reasonably priced GS calipers.

GC, do you have the calipers already?

[GOLDCYLON]

Originally Posted by ghlkal

I'd like to do this also, but I have a hard time finding reasonably priced GS calipers.

GC, do you have the calipers already?

yep bought months ago

[DRM500RUBYZR-1]

Completely replace my valve stem caps; not just one, but all four of them.
The car is up on the lift so this seems like the ideal time to tackle this job that I just keep putting off.


Might also try to clean the entire inside of the front windshield if the winter turns out to be long.


Move the box with the now 3 year old new B&B Fusion Exhaust to the other side of the garage.


Whew......


Marty

[Mystic ZR-1]

Marty
Don't overdue it....
😋

[JThomas]

Originally Posted by -=Jeff=-

Joe,

I suggest the new radio route. If you were going NCRS then stock. But you have changed the color.. go aftermarket. The Sony XAV-AX100 is a nice unit and the XAV-AX200 adds DVD player and SXM. Both have Car Play and Android Auto capability


Sent from my iPhone using ZR-1 Net Registry

Thanks for the suggestions. I will look into those units. As much as I like my music, I have to be honest, whenever I drive the ZR-1, I am usually listening to the "music" made by the motor! I have only turned the radios on in the other two, just to make sure they even worked!

[BigJohn]

Originally Posted by Mystic ZR-1

Marty
Don't overdue it....
😋

You know if you sold me your sunviser I could put it on my 38 chevy.

[Zrracer]

Originally Posted by JThomas

1. Continued cleanup
2. Track down small oil leak
3. Shop for a new radio or upgrade factory unit with modern specs
4. Purchase new glass roof
5. Sort out minor height difference in rear end (Rear spring?)
6. Install new bearings in left headlight, so it rotates smoothly

Make sure you are measuring heights from the frame not the wheel wells.

[LGAFF]

Will get done

24lb injectors
Successful Nitrous Run



Would like to get done

New hard brake lines
C6 Calipers
Mufflers

[jss06c6]

Originally Posted by Ccmano

Just finished...

Flywheel Fidanza, clutch disc, pressure plate, pilot & throwout bearings
Clutch master, slave & steel braided line.
Drive shaft U-joints and C-Beam Plates
Hurst Shifter
Engine mounts
Oil temp & pressure sensors
Power Steering hoses
Headers, Obx Exhaust & new O2 sensors
Front shock bushings
DIC panel replacement
Instrument pod trim replacement

Moving forward she will need a tune (Dom you listening)
Driver seat transmission replacement
Fix the tach (usual incorrect readings)
Alignment

Not sure for this winter but if time and funds permit
Replace all suspension bushings
Port the plenum and injector housings plus power coat.
New carpet.

It’s an on going project...
H

Hans,

How does she run?? Congrats on the progress buddy!!

Steve

Sent from my XT1585 using ZR-1 Net Registry mobile app

[jss06c6]

Originally Posted by DRM500RUBYZR-1

Completely replace my valve stem caps; not just one, but all four of them.
The car is up on the lift so this seems like the ideal time to tackle this job that I just keep putting off.


Might also try to clean the entire inside of the front windshield if the winter turns out to be long.


Move the box with the now 3 year old new B&B Fusion Exhaust to the other side of the garage.


Whew......


Marty

Now that's a good list!!

Sent from my XT1585 using ZR-1 Net Registry mobile app