Carter, new part,I think. - Page 2 - ZR-1 Net Registry Forums

Dynomite · 01-07-2014

Quote:

Originally Posted by efnfast

Sorry Cliff, didn't mean to pick on your solution. If there is nothing commercially available, Carter MUST be able to knock something out. I bet he could even carve LT-5 or something in it.

Ha.....this happened to me before when I got creative but not up to snuff and Carter came up with something much better looking.....so I just create and fool around and wait for carter to make it right

Here is a REAL Example of KLUDGE

if our friend is listening

Carter.....Dude....

As you can see I did not leave much rubber hose to work with but enough for some kind of plug.

carter200 · 01-07-2014

Dyno,
I'll work some magic and replace that sow's ear......

carter200 · 02-04-2014

I just finished the Bypass Plug for efnfast. In the mail to him tomorrow and hopefully he'll post up a pic before and after. Working on front sway bar relocation brackets, LT5 rear plate, billet throttle line brackets then a project for GC.

WVZR-1 · 02-05-2014

I would think something similar to this one. Anything short of "barbed" similar to this I think might fall short. This is maybe an "incorrect" dimension but a correct ID I never did see mentioned. This one is 3/8".

XfireZ51 · 02-05-2014

I run the hoses as if they were operational.

Dynomite · 02-05-2014

Quote:

Originally Posted by carter200

I just finished the Bypass Plug for efnfast. In the mail to him tomorrow and hopefully he'll post up a pic before and after. Working on a LT5 rear plate next then a project for GC.

We need a photo and description of how it fits.......and size

Quote:

Originally Posted by WVZR-1

I would think something similar to this one. Anything short of "barbed" similar to this I think might fall short. This is maybe an "incorrect" dimension but a correct ID I never did see mentioned. This one is 3/8".

The Hose ID is 3/8 inch fitting on a 3/8 inch OD pipe nipple.
You will find the 3/8 inch Aluminum Barbed Hose Plug here....... 3/8 inch Barbed Hose Plug

Quote:

Originally Posted by XfireZ51

I run the hoses as if they were operational.

What else are you faking

I run my ZR-1 as if it were stock around CA Highway Patrol......

efnfast · 02-10-2014

Carter stuff just arrived. My plug, oil filter cover, oil filler cover, power steering and brake fluid. Gimme a minute, I'll get it installed.

carter200 · 02-10-2014

Quote:

Originally Posted by efnfast

Carter stuff just arrived. My plug, oil filter cover, oil filler cover, power steering and brake fluid. Gimme a minute, I'll get it installed.

PM me with your findings.....

efnfast · 02-10-2014

I used a Gates heat shrink for the plug. Looks the nuts. This is a must if you've eliminated the tb coolant.

Dynomite · 02-10-2014

Quote:

Originally Posted by efnfast

Carter stuff just arrived. My plug, oil filter cover, oil filler cover, power steering and brake fluid. Gimme a minute, I'll get it installed.

Do you have a nice photo of that TB Coolant Plug Carter came up with I been waiting for

And Carter.....Just look at my thread and make a Billet Oil Dip Stick Handle.....there is enough information there to crank (excuse me....turn) one out I am sure.....

AMSOIL 10W-40 Etched in Red Letters

See Item #3 LT5 Lubrication Tricks

01-07-2014	#12
carter200 Join Date: Jun 2004 Location: Texas Posts: 2,431	Re: Carter, new part,I think. Dyno, I'll work some magic and replace that sow's ear...... __________________ 95 ZR-1 BLK/Gry #392 LT5 Reg# 868 RIP ZR1NET Founding Mem #155

02-04-2014	#13
carter200 Join Date: Jun 2004 Location: Texas Posts: 2,431	Re: Carter, new part,I think. I just finished the Bypass Plug for efnfast. In the mail to him tomorrow and hopefully he'll post up a pic before and after. Working on front sway bar relocation brackets, LT5 rear plate, billet throttle line brackets then a project for GC. __________________ 95 ZR-1 BLK/Gry #392 LT5 Reg# 868 RIP ZR1NET Founding Mem #155 Last edited by carter200; 02-11-2014 at 12:37 AM.

02-05-2014	#14
WVZR-1 Join Date: Oct 2004 Posts: 1,889	Re: Carter, new part,I think. I would think something similar to this one. Anything short of "barbed" similar to this I think might fall short. This is maybe an "incorrect" dimension but a correct ID I never did see mentioned. This one is 3/8". Last edited by WVZR-1; 02-05-2014 at 05:00 AM.

02-05-2014	#15
XfireZ51 Join Date: May 2007 Location: Chicagoland, IL Posts: 9,678	Re: Carter, new part,I think. I run the hoses as if they were operational. __________________ [SIGPIC][/SIGPIC]Former Membership Chairman Former ZR-1 Registry - BOD 1972 Corvette 4speed base Coupe SOLD long time ago 1984 Corvette Z-51/4+3 SOLD 1992 Corvette ZR-1 Aqua/Gray #474 SOLD 1992 Corvette ZR-1 Black Rose/Cognac #458 2014 Honda VFR Interceptor DX

02-10-2014	#17
efnfast Join Date: Nov 2011 Location: Dunbarton NH Posts: 7,283	Re: Carter, new part,I think. Carter stuff just arrived. My plug, oil filter cover, oil filler cover, power steering and brake fluid. Gimme a minute, I'll get it installed.

02-10-2014	#19
efnfast Join Date: Nov 2011 Location: Dunbarton NH Posts: 7,283	Re: Carter, new part,I think. I used a Gates heat shrink for the plug. Looks the nuts. This is a must if you've eliminated the tb coolant.