Header install questions. - Page 2 - ZR-1 Net Registry Forums

Paul Workman · 05-23-2010

The 5 of you that expressed an interest in me making them a dipstick tube bracket to secure the dipstick when using the Stainless Works headers...Your brackets are ready. I'll get them mailed out Monday and let ya know 'bout the cost. I'll PM ya (you know who you are).

They are a little crude, as the grinding is not machined, but done w/ a hand-held grinder, doancha know. But, that is not visible when the bracket is installed and the bracket itself is rather obscure, normally.

I'll PM each of y'all.

P.

HAWAIIZR-1 · 05-23-2010

Paul,

Thank you very much. It looks great and I think you might end up getting many more orders. I have a custom made Lokar oil dip stick but not satisfied with my bracket and this will work much better or I might be able to modify my Lokar to your bracket and get the best of both worlds.

Aloha,

Craig

todesengel · 05-23-2010

helluva a gesture

Quote:

Originally Posted by Paul Workman

The 5 of you that expressed an interest in me making them a dipstick tube bracket to secure the dipstick when using the Stainless Works headers...Your brackets are ready. I'll get them mailed out Monday and let ya know 'bout the cost. I'll PM ya (you know who you are).

They are a little crude, as the grinding is not machined, but done w/ a hand-held grinder, doancha know. But, that is not visible when the bracket is installed and the bracket itself is rather obscure, normally.

I'll PM each of y'all.

P.

pantera1683 · 05-23-2010

Yippee! I just finished the header install yesterday. Thanks so much Paul.

Kris

aod · 05-23-2010

Thanks Paul, you rock!

ZZZZZR1 · 05-23-2010

Quote:

Originally Posted by aod

Thanks Paul, you rock!

I agree! Paul you da man!

billybaloneey · 05-24-2010

Thanks for going above and beyond.

aod · 05-24-2010

I guess my final question, before I embark on this journey, is what things should be wrapped to protect it from heat and what was used to wrap it with?

pantera1683 · 05-24-2010

Quote:

Originally Posted by aod

I guess my final question, before I embark on this journey, is what things should be wrapped to protect it from heat and what was used to wrap it with?

What year is yours? I think the early ones require some heat shielding. I have a 94 and with SW headers I didn't have to wrap anything. I just zip tied the O2 sensor wires away from the headers. Oh yeah, my headers are ceramic coated too, so I wasn't all that concerned with heat.

aod · 05-24-2010

Quote:

Originally Posted by pantera1683

What year is yours? I think the early ones require some heat shielding. I have a 94 and with SW headers I didn't have to wrap anything. I just zip tied the O2 sensor wires away from the headers. Oh yeah, my headers are ceramic coated too, so I wasn't all that concerned with heat.

Mine is a '90.

05-23-2010	#11
Paul Workman Join Date: Nov 2007 Location: Squires (near Ava MO in the Mark Twain N'tl Forest) - Missouri Posts: 6,493	Re: Calling all that wanted dipstick tube brackets... The 5 of you that expressed an interest in me making them a dipstick tube bracket to secure the dipstick when using the Stainless Works headers...Your brackets are ready. I'll get them mailed out Monday and let ya know 'bout the cost. I'll PM ya (you know who you are). They are a little crude, as the grinding is not machined, but done w/ a hand-held grinder, doancha know. But, that is not visible when the bracket is installed and the bracket itself is rather obscure, normally. I'll PM each of y'all. P. __________________ Good carz, good food, good friendz = the best of timez! 90 #1202 "FBI" top end ported & relieved Cam timing by "Pete the Greek" Sans secondaries Chip & dyno tuning by Haibeck Automotive SW headers, X-pipe, MF muffs Former Secretary, ZR-1 Net Registry

05-23-2010	#12
HAWAIIZR-1 Join Date: May 2010 Location: Japan Posts: 3,543	Re: Header install questions. Paul, Thank you very much. It looks great and I think you might end up getting many more orders. I have a custom made Lokar oil dip stick but not satisfied with my bracket and this will work much better or I might be able to modify my Lokar to your bracket and get the best of both worlds. Aloha, Craig __________________ Craig "ZR-1 NO KA 'OI" "ZR-1 ICHIBAN" 1995 #228 Black/Black with Dunn Heads ZR-1 owner since September 2003 ZR-1 Net Registry Founding Member #0074 NCM Lifetime Member #2048

05-23-2010	#14
pantera1683 Join Date: Mar 2010 Location: Fort Worth, TX Posts: 396	Re: Header install questions. Yippee! I just finished the header install yesterday. Thanks so much Paul. Kris

05-23-2010	#15
aod Join Date: Aug 2009 Location: Green Bay, WI Posts: 50	Re: Header install questions. Thanks Paul, you rock!

05-24-2010	#17
billybaloneey Join Date: May 2008 Location: Mauriceville, Texas Posts: 179	Re: Header install questions. Thanks for going above and beyond. __________________ Clint aka billybaloneey '94 - C4 ZR-1 #445 - Black/Black '05 - C6 silver/black 6sp '85 - C4 white/graphite (almost done) automatic '78 - C3 silver/black (a work in progress) automatic

05-24-2010	#18
aod Join Date: Aug 2009 Location: Green Bay, WI Posts: 50	Re: Header install questions. I guess my final question, before I embark on this journey, is what things should be wrapped to protect it from heat and what was used to wrap it with?