Update on my hi-miler Z project - Page 33 - ZR-1 Net Registry Forums

cvette98pacecar · 07-07-2012

Quote:

Originally Posted by Kevin

i have two headliners that need done

I have to do my headliner, anyone know where to send sun visors?

USAFPILOT · 07-08-2012

got pictures of the fix?

VetteMed · 07-08-2012

Quote:

Originally Posted by USAFPILOT

got pictures of the fix?

Unfortunately, no. I was in a hurry to finish because I was excited to feel 42 degree air coming from the vents

Not much to see though. I started out with "the right stuff" RTV, but that was difficult to apply in some spots due to limited access.

I stuffed some foam strips in to fill up most of the space, then used the butyl rope type stuff to seal it up and close the gap fully. most parts stores sell the butyl material in a thin cardboard box, near the adhesives and such.

VetteMed · 07-09-2012

101 degrees today, with 43 degree air in my face! Loving it! Just had to share with some folks who would appreciate it!!

tf95ZR1 · 07-09-2012

Congratulations on diagnosing and solving your problem.
Nothing like celebrating the fruits of your
labor! Stay Cool!

GOLDCYLON · 05-15-2014

Many thanks to Vettemed. Folks take note of Andrews post #318 if you are having dimished AC performance after replacing the evaporator core. Last summer my car in my opinion was not cooling down as much as it used to do in heavy AC load conditions in the 118-122 dog days of summer in Arizona. It always used to be a lot colder from my memory and since reparing the AC a year or so ago with all new parts I just could not figure out what was going on. I remembered this post up as Andrew was having the same problems. I put this on the long list of projects I wanted to complete this winter. I missed it however and it didnt make it to the list last winter, Tuesday of this week was a uber rare Santa Ana winds fed blustery day here in AZ and the evening temps in the garage were in the 70s and I said well... now or never. I had my evaporator core replaced while I was TDY at work so I never saw the original unit that was removed. Long story short I had the exact same gap on the left side of the heater core that Andrew has pictured in picture #1 of post #318. So I fed gray foam material, the kind used to protect guns and hard drives into that vertical slot. Walla.. in 100 degree temps yesterday the AC was spitting out 46 Degee air.

This view is what you might see if you pull the blower motor and look towards the evaporator core. See that vertical gap? it should not be there. As Andrew stated in his post either the replacement core is shorter than stock or it is factory foamed in on that side. Make sure you or your installer is aware of this issue so they can address it at time of replacement. Andrew was 100% correct with the gap hot air was bypassed into the system and mixing into the cooler air. The concept or idea is that you want everything intaked and passed through that core.

-=Jeff=- · 05-15-2014

Cool yet something more for me to check

GOLDCYLON · 05-15-2014

Quote:

Originally Posted by -=Jeff=-

Cool yet something more for me to check

After you make me a down in one harness

07-08-2012	#322
USAFPILOT Join Date: Aug 2007 Location: Spring TX Posts: 1,348	Re: Update on my hi-miler Z project got pictures of the fix? __________________ 1994 #293 ZR-1 Stainless Works Long Tube Headers, B&B catback w/ X-Pipe, 18" Shelby Series One Wheels, SLP CAI.

07-09-2012	#324
VetteMed Join Date: Mar 2009 Location: Orlando, FL Posts: 1,828	Re: Update on my hi-miler Z project 101 degrees today, with 43 degree air in my face! Loving it! Just had to share with some folks who would appreciate it!! __________________ 2004 Z06/Z16 LeMans Commemorative Edition 1991 ZR-1 #302 White/Gray (sold) 1991 ZR-1 #1147 Red/Saddle (sold)

07-09-2012	#325
tf95ZR1 Join Date: Aug 2005 Location: Northridge, CA Posts: 1,445	Re: Update on my hi-miler Z project Congratulations on diagnosing and solving your problem. Nothing like celebrating the fruits of your labor! Stay Cool!

05-15-2014	#326
GOLDCYLON Join Date: May 2007 Location: Peoria, AZ Posts: 9,153	Re: Update on my hi-miler Z project Many thanks to Vettemed. Folks take note of Andrews post #318 if you are having dimished AC performance after replacing the evaporator core. Last summer my car in my opinion was not cooling down as much as it used to do in heavy AC load conditions in the 118-122 dog days of summer in Arizona. It always used to be a lot colder from my memory and since reparing the AC a year or so ago with all new parts I just could not figure out what was going on. I remembered this post up as Andrew was having the same problems. I put this on the long list of projects I wanted to complete this winter. I missed it however and it didnt make it to the list last winter, Tuesday of this week was a uber rare Santa Ana winds fed blustery day here in AZ and the evening temps in the garage were in the 70s and I said well... now or never. I had my evaporator core replaced while I was TDY at work so I never saw the original unit that was removed. Long story short I had the exact same gap on the left side of the heater core that Andrew has pictured in picture #1 of post #318. So I fed gray foam material, the kind used to protect guns and hard drives into that vertical slot. Walla.. in 100 degree temps yesterday the AC was spitting out 46 Degee air. This view is what you might see if you pull the blower motor and look towards the evaporator core. See that vertical gap? it should not be there. As Andrew stated in his post either the replacement core is shorter than stock or it is factory foamed in on that side. Make sure you or your installer is aware of this issue so they can address it at time of replacement. Andrew was 100% correct with the gap hot air was bypassed into the system and mixing into the cooler air. The concept or idea is that you want everything intaked and passed through that core. __________________ GOLDCYLON - 91 ZR-1 #2014 GOLDCYLON - 90 ZR-1 #2794, 4L60e (Formerly Schrade's) GOLDCYLON - 11 CTS-V Arizona State Director 91 WHITE/BLACK #2014. 380 P&P&PCed,Ported Heads, Jeal Long tubes, Corsa Exhaust/FIKSE FM-5s /LED TLs, LED Headlights, Front Wilwood 6 piston narrowlite calipers and rear Wilwood caliper street shop mod,CNCed Coolant Pipes,TPI Cvr,Filter cover,Stainless Bolts, DRM/DOM PROM /ZFDOC mod build #102,DRLs,BMAD with stainless Debris Screen,Coplan Air Blaster, Pioneer APP Radio 4,Brey-Krause HB,Sub Bar,Fire extinguisher seat mount,DRM Coilovers,LEDs everywhere,Compass mirror (orange),V1 DIC hidden display, Homelink sun visor, Carbon Fiber top x3 and APSIS Carbon Fiber interior, APSIS CF Steering Wheel/NAPA Leather, Banski trailing arms, Guldstrand front suspension,urethane bushings from Prothane (total suspension) ZFDoc drive shaft safety loop, raptor shift light (orange),AO engineering louver front plate, Console seat cushion, 96CE seats with black custom Sheepskins, ss billet catch can,Viper remote entry/alarm,Cragar Rear Louvers,LED side louver lights, Dewitts Radiator with SPAL fans and a Woods 160 T-Stat 90 RED/BLACK #2794. 4L60e Automatic Stage V by RPM Transmission, TCI Dedicated TCM, OBX Stainless Headers, Corsa Exhaust, SAN Secondaries and Haibeck PROM, Exotic Muscle Coil overs, LED Interior Lights, LED Tail Lights, LED Headlights, 94 Sport seats with black custom Sheepskins , Cragar rear louvers, GS Front calipers, Banski Trailing arms, APSIS Carbon Fiber steering wheel, Front and Rear Baer Eradispeeds, DRLs, Guldstrand front suspension,urethane bushings from Prothane (total suspension), Dewitt's Raditor with Dual SPAL fans and a Haibeck 170 T-Stat 11 RED/GREY CTS-V Last edited by GOLDCYLON; 05-15-2014 at 12:18 PM.

05-15-2014	#327
-=Jeff=- Join Date: Jul 2007 Location: Bartlett, IL Posts: 7,132	Re: Update on my hi-miler Z project Cool yet something more for me to check __________________ 1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - 3" Magnaflow Bullet cats - LT4 Catback Late Model IH - Plenum Coilovers - 4.10s Custom Interior NCM Lifetime Member #978