02-16-2010 | #1 |
Join Date: Aug 2006
Location: McLean, VA
Posts: 3,707
|
"C" beam plates
A couple of questions regarding beam plates:
1. Where can I get them? 2. Is it necessary to remove exhasust to install? Is it relatively simple procedure? |
02-16-2010 | #2 |
Join Date: Oct 2004
Location: Folsom CA
Posts: 1,645
|
Re: "C" beam plates
They're made by Bill Boudreau, the "ZF Doc":
http://www.zfdoc.com/c4beamplate.htm They're not that hard to put on, figure on spending a Sunday afternoon, 2 or 3 hours at most. It might be possible to put them on with the exhaust in place, but there's not a lot of room under there. It's not that difficult to remove the exhaust. TomC 'Crabs
__________________
TomC '90ZR1 #792 Honorary Pirate [B]If it ain't FUN, you're doing something terribly WRONG. [/B] |
02-16-2010 | #3 | |
Join Date: Feb 2009
Location: Alexandria, Virginia
Posts: 1,469
|
Re: "C" beam plates
Quote:
I put mine on when I installed my 4.10's and had the exhaust off anyway. I don't think you would have enough room to get the bolts out with the exhaust in the way. It's a piece of cake once you have the exhaust off Sounds like a job for WAZOO!!! Rich
__________________
1990 Bright Red Coupe #608 380 Stroker, Ported Heads/Intake/Housings/TB Haibeck Secondary Delete Chip / Pete's Cams George Braml Intake / FIC Injectors Coated SW Headers / Corsa Bill Boudreau B/B ZF6 / Viper 4.10 gears Ron Davis Radiator Pioneer AVIC-Z140BH NAV Fikse FM5's 285 / 335 / C6 Brakes WAZOO Member |
|
02-16-2010 | #4 |
Join Date: Aug 2006
Location: McLean, VA
Posts: 3,707
|
Re: "C" beam plates
Thanks guys.
Yes, Rich. Sounds like one of my "to do" list item. Rich, Did you notice any difference after the install? |
02-16-2010 | #5 | |
Join Date: Feb 2009
Location: Alexandria, Virginia
Posts: 1,469
|
Re: "C" beam plates
Quote:
Rich
__________________
1990 Bright Red Coupe #608 380 Stroker, Ported Heads/Intake/Housings/TB Haibeck Secondary Delete Chip / Pete's Cams George Braml Intake / FIC Injectors Coated SW Headers / Corsa Bill Boudreau B/B ZF6 / Viper 4.10 gears Ron Davis Radiator Pioneer AVIC-Z140BH NAV Fikse FM5's 285 / 335 / C6 Brakes WAZOO Member |
|
02-16-2010 | #6 | |
Join Date: Oct 2004
Location: Folsom CA
Posts: 1,645
|
Re: "C" beam plates
Quote:
Worth every penny. TomC 'Crabs
__________________
TomC '90ZR1 #792 Honorary Pirate [B]If it ain't FUN, you're doing something terribly WRONG. [/B] |
|
02-16-2010 | #7 |
Join Date: May 2007
Location: Westminster, Maryland
Posts: 3,687
|
Re: "C" beam plates
Once some of this snow melts, we will schedule a WMD and we can put the C-Beam Plates on your car. I have a set here that you are welcome to use and replace if it turns into a long-lead time item.
Jim |
02-16-2010 | #8 |
Join Date: Oct 2004
Location: Folsom CA
Posts: 1,645
|
Re: "C" beam plates
You might want to check with ZFACTOR, we may have some available at the Registry store.
JeffVette may have a set or two also. TomC 'Crabs
__________________
TomC '90ZR1 #792 Honorary Pirate [B]If it ain't FUN, you're doing something terribly WRONG. [/B] |
02-16-2010 | #9 |
Join Date: Sep 2006
Location: lone pine and mammoth lakes
Posts: 1,407
|
Re: "C" beam plates
i have them on both my cars ,and love them . especially when you get on her in first gear and hit second the car goes dead straight .before them she really kicked out the rear end . and the other plus is ,if and when, you have to remove the rear end and tranny it makes short work of putting the bolts back on. to me its a must do
|
02-16-2010 | #10 |
Join Date: Aug 2006
Location: McLean, VA
Posts: 3,707
|
Re: "C" beam plates
Thanks guys.
I will order from ZF doc and see. Thanks for the offer Jim. Hopefully it's not a long lead item. |
|
|