|
12-19-2017 | #1 |
Join Date: Sep 2016
Location: Ocala, FL
Posts: 879
|
Re: WANTED: Cam position sensor and Dual mass flywheel for 1990 ZR1 LT5
I can have it removed and on the bench by the top of the hour. Heading home now.
Sent from my iPhone using ZR-1 Net Registry
__________________
Steve Young 1991 ZR-1 Quasar Blue Metallic/Black #729 Second Owner 1991 ZR-1 Dark Red Metallic/Black #2040 SOLD 1990 ZR-1 Dark Red Metallic/Saddle #1670 SOLD Double your happiness.....complain half as much. |
12-19-2017 | #2 |
Join Date: Sep 2016
Location: Ocala, FL
Posts: 879
|
Re: WANTED: Cam position sensor and Dual mass flywheel for 1990 ZR1 LT5
WVZR-1 sensor is on the bench. It is original part 10096172. What next? I shall PM you my phone number.
Sent from my iPhone using ZR-1 Net Registry
__________________
Steve Young 1991 ZR-1 Quasar Blue Metallic/Black #729 Second Owner 1991 ZR-1 Dark Red Metallic/Black #2040 SOLD 1990 ZR-1 Dark Red Metallic/Saddle #1670 SOLD Double your happiness.....complain half as much. |
12-19-2017 | #3 |
Join Date: Oct 2004
Posts: 1,889
|
Re: WANTED: Cam position sensor and Dual mass flywheel for 1990 ZR1 LT5
|
12-19-2017 | #4 |
Join Date: Oct 2004
Posts: 1,889
|
Re: WANTED: Cam position sensor for LT5
Phil has sent me all of the information I need and I'm very sure my information is correct. I'm going to compile everything and forward it to Phil for confirmation.
Young1 - All's well - if you send me snapshots that's fine - if not I believe I'm OK without. |
12-19-2017 | #5 |
Join Date: Dec 2003
Location: Arcadia,OK
Posts: 3,374
|
Re: WANTED: Cam position sensor for LT5
Not just good luck, but GREAT LUCK!!
__________________
Jerry Downey JERRYS LT5 GASKETS & PARTS http://www.jerrysgaskets.com 1994 ZR-1, Black/Black, Lingenfelter Aerobody, 416cu in, 3.91 gears, coil-over susp, Brembo brakes, etc. 2016 Black-Red, 3LT-Z51 Auto 8-speed. |
12-19-2017 | #6 |
Join Date: Sep 2016
Location: Ocala, FL
Posts: 879
|
Re: WANTED: Cam position sensor and Dual mass flywheel for 1990 ZR1 LT5
__________________
Steve Young 1991 ZR-1 Quasar Blue Metallic/Black #729 Second Owner 1991 ZR-1 Dark Red Metallic/Black #2040 SOLD 1990 ZR-1 Dark Red Metallic/Saddle #1670 SOLD Double your happiness.....complain half as much. |
12-19-2017 | #7 |
Join Date: Apr 2007
Location: Northern VA
Posts: 2,644
|
Re: WANTED: Cam position sensor and Dual mass flywheel for 1990 ZR1 LT5
__________________
Phil Wasinger 1994 Torch Red ZR-1 WAZOO Member George Braml Intake |
12-20-2017 | #8 |
Join Date: Jun 2006
Location: Sparks, NV
Posts: 2,852
|
Re: WANTED: Cam position sensor for LT5
Looks the same as an O2 sensor connector.
H
__________________
90'ZR-1 #1461 Red/Black Ported Intake, Degreed Cams, OBX Headers & Exhaust, Fidanza FW, Secondary Delete, Custom tune, C6 GS Wheels. Sold 08 C6 Z51 Crystal Red Metallic Sold Vararam Intake, Tune, Sold 05 C6 Z51 Red/Black Sold 90'ZR-1 #1723 Black/Gray Sold but not forgotten 91' Z51 L98 White Vert. My First, you always remember your first. Sold. |
12-20-2017 | #9 |
Join Date: Dec 2007
Location: Fremont,Ca
Posts: 3,039
|
Re: WANTED: Cam position sensor for LT5
I can’t post pictures here of what I have but somebody send me an email and I’ll send a few pictures when I get off work. I’ve used these terminals when I put the Euro taillights in my car.
|
12-20-2017 | #10 |
Join Date: Oct 2004
Posts: 1,889
|
Re: WANTED: Cam position sensor for LT5
Until Phil has the sensor and confirms the configuration of the sensor to the cavity the connector is of little concern. I've ID'd the connector shell and supplied Phil with all of the tools needed to evaluate components and eliminate guessing. The terminals and seals need to be selective based upon the wire gauge of the sensor he's considered.
I'd say the project is 'under control'! Jeff - your sources are valid for parts. I used another but I was buying in bulk when I was purchasing. |
|
|