ZR-1 Net Registry Forums  

Go Back   ZR-1 Net Registry Forums > C4 ZR-1 > C4 ZR-1 Technical Postings

Reply
 
Thread Tools Display Modes
Old 10-14-2013   #1
POWERBRAKEBOB
 
Join Date: Apr 2010
Location: HUNTINGTON BEACH, CALIF.
Posts: 38
Default HYDROBOOST INSTALLATION

Hi Gang! I have been dissatisfied with the look of the vacuum booster, and the computer and huge wiring loom plopped on top of the vacuum booster. The master and vac booster were getting tired at 260,000 miles. Since I am in the business of custom brake conversions. I built a HYDROBOOST unit for my car. This one is Silver Sparkle Powdercoated. Soon, I will remove the top side of the engine, and powdercoat plenum, cam covers, and IH to match. The stopping power is incredible! The Hydroboost really pulls the car down in a hurry.
Attached Images
File Type: jpg IMG_4191.jpg (137.8 KB, 43 views)
File Type: jpg IMG_4712.jpg (88.5 KB, 61 views)
POWERBRAKEBOB is offline   Reply With Quote
Old 10-14-2013   #2
LGAFF
 
LGAFF's Avatar
 
Join Date: Mar 2007
Location: Crystal Lake, IL
Posts: 7,191
Default Re: HYDROBOOST INSTALLATION

Does this system run off the P/S pump?
__________________
LGAFF
90 #966-150K miles-sold
92 #234-sold
1987 Callaway TT #17
1991 ZR-1 #1359
LGAFF is offline   Reply With Quote
Old 10-14-2013   #3
Don in VT
 
Join Date: Jul 2010
Location: Fairfax, VT
Posts: 203
Default Re: HYDROBOOST INSTALLATION

Based on the pic the HB could have it's own pump.
Don in VT is offline   Reply With Quote
Old 10-14-2013   #4
XfireZ51
 
Join Date: May 2007
Location: Chicagoland, IL
Posts: 9,669
Default Re: HYDROBOOST INSTALLATION

PBB,

Are you a vendor?
__________________
[SIGPIC][/SIGPIC]Former Membership Chairman
Former ZR-1 Registry - BOD
1972 Corvette 4speed base Coupe SOLD long time ago
1984 Corvette Z-51/4+3 SOLD
1992 Corvette ZR-1 Aqua/Gray #474 SOLD
1992 Corvette ZR-1 Black Rose/Cognac #458
2014 Honda VFR Interceptor DX
XfireZ51 is offline   Reply With Quote
Old 10-15-2013   #5
icarus-54
 
icarus-54's Avatar
 
Join Date: Jul 2013
Location: Mt.Bethel Pa.
Posts: 73
Default Re: HYDROBOOST INSTALLATION

I have hydro boost brakes in my syclone,less clutter,considerably more clamping power.With vacuum brakes I could only hold 7 psi on the brakes,but with hydro boost I can hold over 12 psi.I used a set up out of a 95 astro van,turned it upside down so the lines were more direct to the ps pump.
__________________
1990 Zr-1 #361
1991 GMC Syclone (built)
1993 GMC Typhoon (stock)
1993 GMC Typhoon (street)
1992 GMC Sonoma GT
1928 Model A pick up
icarus-54 is offline   Reply With Quote
Old 10-15-2013   #6
-=Jeff=-
 
-=Jeff=-'s Avatar
 
Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,132
Default Re: HYDROBOOST INSTALLATION

from your post in another thread:
Quote:
Originally Posted by POWERBRAKEBOB View Post
The piston size in the calipers is small. The C5 calipers are much larger pistons. Nice, but that requires a larger master cylinder to provide the needed volume. C5's and C6's used 1" masters. The bolt pattern on the C4 boosters does not allow for master cylinder upgrading.
You can install a 1" Master from a 98-later F-body on the ZR-1 it will bolt up.. needs a spacer (or the end drilled) to get it just right.

So with some of these guys doing C6 Z06 brakes all around, what Master do you suggest? will a 1" be enough?

THEN, which master is correct as you want to be sure the bias is correct front to rear too right?
__________________
1990 Corvette ZR-1 #1051
Watson Headers (2" Primary) - 3" Magnaflow Bullet cats - LT4 Catback
Late Model IH - Plenum
Coilovers - 4.10s
Custom Interior
NCM Lifetime Member #978
-=Jeff=- is offline   Reply With Quote
Old 10-23-2013   #7
-=Jeff=-
 
-=Jeff=-'s Avatar
 
Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,132
Default Re: HYDROBOOST INSTALLATION

Quote:
Originally Posted by -=Jeff=- View Post
from your post in another thread:


You can install a 1" Master from a 98-later F-body on the ZR-1 it will bolt up.. needs a spacer (or the end drilled) to get it just right.

So with some of these guys doing C6 Z06 brakes all around, what Master do you suggest? will a 1" be enough?

THEN, which master is correct as you want to be sure the bias is correct front to rear too right?
???
__________________
1990 Corvette ZR-1 #1051
Watson Headers (2" Primary) - 3" Magnaflow Bullet cats - LT4 Catback
Late Model IH - Plenum
Coilovers - 4.10s
Custom Interior
NCM Lifetime Member #978
-=Jeff=- is offline   Reply With Quote
Old 10-23-2013   #8
Kevin
 
Kevin's Avatar
 
Join Date: Jun 2005
Location: pittsburgh
Posts: 4,633
Default Re: HYDROBOOST INSTALLATION

hit and run
__________________
It's not the car, it's the people - Doug Johnson
90 r/r "KEYS ON" nick named "T.L.B"
Kevin is offline   Reply With Quote
Old 10-23-2013   #9
ghlkal
 
ghlkal's Avatar
 
Join Date: Jan 2012
Location: Wisconsin
Posts: 882
Default Re: HYDROBOOST INSTALLATION

Quote:
Originally Posted by POWERBRAKEBOB View Post
Hi Gang! I have been dissatisfied with the look of the vacuum booster, and the computer and huge wiring loom plopped on top of the vacuum booster.

I'm interested in where you moved the computer ...
ghlkal is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:52 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright ZR-1 Net Registry 2020