|
12-16-2020
|
#11 |
 
Join Date: Jan 2009
Location: New jersey
Posts: 156
|
Re: Best Place to Buy Injectors?
I have to ask, what flow rate are the FIC injectors for the Stock lt5? I have heard 20 pounds. and if this is true, what pound injector would be good for a 700 motor? I am overthinking getting Accell 21 pound injectors feeling that they are going to be too small...
John |
|
|
|
12-16-2020
|
#12 | |
 
Join Date: Dec 2003
Location: Arcadia,OK
Posts: 3,372
|
Re: Best Place to Buy Injectors?
Quote:
__________________
Jerry Downey JERRYS LT5 GASKETS & PARTS http://www.jerrysgaskets.com 1994 ZR-1, Black/Black, Lingenfelter Aerobody, 416cu in, 3.91 gears, coil-over susp, Brembo brakes, etc. 2016 Black-Red, 3LT-Z51 Auto 8-speed. |
|
|
|
|
|
12-16-2020
|
#13 |
|
Join Date: Nov 2016
Location: New Brunswick
Posts: 934
|
Re: Best Place to Buy Injectors?
My set arrived lightning fast from Jerry. Oddly enough, considering the volumes this time of year, it was the fastest delivery I've had yet.
__________________
1990 ZR-1 # 996 "All Corvettes are red. The rest are mistakes." - John Heinricy |
|
|
|
|
06-06-2021
|
#14 |
|
Join Date: Nov 2016
Location: New Brunswick
Posts: 934
|
Re: Best Place to Buy Injectors?
Just to follow up on this, got Jerry's injectors installed, and what a wonderful difference. Smoothed out dramatically right away. Ran through the tank of old gas, gave it a tank of the fresh stuff, and she just began to sing. What a sweetheart of an engine the LT5 is.
__________________
1990 ZR-1 # 996 "All Corvettes are red. The rest are mistakes." - John Heinricy |
|
|
|
|
06-06-2021
|
#15 |
Join Date: Jan 2021
Location: Beautiful Bavaria
Posts: 517
|
Re: Best Place to Buy Injectors?
Glad to hear, congrat! Enjoy the ride, finally it's nearly already spring now
 Sent from my SM-G991B using ZR-1 Net Registry mobile app
__________________
ZR-1 #638/1991 |
|
|
|
|
06-12-2021
|
#16 | |
 
Join Date: Nov 2007
Location: Squires (near Ava MO in the Mark Twain N'tl Forest) - Missouri
Posts: 6,493
|
Re: Best Place to Buy Injectors?
Quote:
Before the FIC/Jerrys Gasket marriage, I turned to the Summit Racing #150821s 21# rated) back in 2012 (IIRC) and have had ZERO problems since! The only mod required is grinding off the little plastic indexing (connector) nub for use in the secondary ports only. And, I can tell ya they support 510+ HP w/o any problem in the past 9+ years!
__________________
Good carz, good food, good friendz = the best of timez! 90 #1202 "FBI" top end ported & relieved Cam timing by "Pete the Greek" Sans secondaries Chip & dyno tuning by Haibeck Automotive SW headers, X-pipe, MF muffs Former Secretary, ZR-1 Net Registry |
|
|
|
|
|
12-19-2023
|
#17 |
|
Join Date: May 2007
Location: Chicagoland, IL
Posts: 9,661
|
Re: Best Place to Buy Injectors?
RC Engineering has an easy BSFC CALCULATOR to help determine injector flow required to support a desired CHP. The stock injector flow is good enough for ~ 540chp w an 80% headroom from static.
I would also recommend not taking flow rates for granted from the supplier and get the Injector Voltage Offset(if available)for better idle performance. You?d be surprised at how much smoother the motor runs when cylinder fuel flow is evenly matched. https://www.rcfuelinjection.com/Technical
__________________
[SIGPIC][/SIGPIC]Former Membership Chairman Former ZR-1 Registry - BOD 1972 Corvette 4speed base Coupe SOLD long time ago 1984 Corvette Z-51/4+3 SOLD 1992 Corvette ZR-1 Aqua/Gray #474 SOLD 1992 Corvette ZR-1 Black Rose/Cognac #458 2014 Honda VFR Interceptor DX Last edited by XfireZ51; 12-19-2023 at 11:14 AM. |
|
|
|
|
01-18-2024
|
#18 |
 
Join Date: Sep 2008
Location: Speedway, IN
Posts: 118
|
Re: Best Place to Buy Injectors?
I?ve had the RC in my 1991 ZR-1 for 13 years. No issues and very smooth.
Sent from my iPhone using ZR-1 Net Registry |
|
|
|
|
01-27-2024
|
#19 |
|
Join Date: Jun 2005
Location: CenCoast California
Posts: 899
|
Re: Best Place to Buy Injectors?
I had RC Injectors in my 95 for most of the 20 years I owned it.
__________________
Hib Halverson Technical Writer former owner 95 VIN 0140 current owner 19 VIN 1878 |
|
|
|
|
01-28-2024
|
#20 |
  
Join Date: May 2007
Location: Peoria, AZ
Posts: 9,152
|
Re: Best Place to Buy Injectors?
Install RCs and then forget about them. Most dependable on the market followed by FICs and or Accels.
__________________
GOLDCYLON - 91 ZR-1 #2014 GOLDCYLON - 90 ZR-1 #2794, 4L60e (Formerly Schrade's) GOLDCYLON - 11 CTS-V Arizona State Director  91 WHITE/BLACK #2014. 380 P&P&PCed,Ported Heads, Jeal Long tubes, Corsa Exhaust/FIKSE FM-5s /LED TLs, LED Headlights, Front Wilwood 6 piston narrowlite calipers and rear Wilwood caliper street shop mod,CNCed Coolant Pipes,TPI Cvr,Filter cover,Stainless Bolts, DRM/DOM PROM /ZFDOC mod build #102,DRLs,BMAD with stainless Debris Screen,Coplan Air Blaster, Pioneer APP Radio 4,Brey-Krause HB,Sub Bar,Fire extinguisher seat mount,DRM Coilovers,LEDs everywhere,Compass mirror (orange),V1 DIC hidden display, Homelink sun visor, Carbon Fiber top x3 and APSIS Carbon Fiber interior, APSIS CF Steering Wheel/NAPA Leather, Banski trailing arms, Guldstrand front suspension,urethane bushings from Prothane (total suspension) ZFDoc drive shaft safety loop, raptor shift light (orange),AO engineering louver front plate, Console seat cushion, 96CE seats with black custom Sheepskins, ss billet catch can,Viper remote entry/alarm,Cragar Rear Louvers,LED side louver lights, Dewitts Radiator with SPAL fans and a Woods 160 T-Stat 90 RED/BLACK #2794. 4L60e Automatic Stage V by RPM Transmission, TCI Dedicated TCM, OBX Stainless Headers, Corsa Exhaust, SAN Secondaries and Haibeck PROM, Exotic Muscle Coil overs, LED Interior Lights, LED Tail Lights, LED Headlights, 94 Sport seats with black custom Sheepskins , Cragar rear louvers, GS Front calipers, Banski Trailing arms, APSIS Carbon Fiber steering wheel, Front and Rear Baer Eradispeeds, DRLs, Guldstrand front suspension,urethane bushings from Prothane (total suspension), Dewitt's Raditor with Dual SPAL fans and a Haibeck 170 T-Stat 11 RED/GREY CTS-V |
|
|
|
 |
|
|
Linear Mode
