Are These the Correct LEDs?

[32valvZ]

New Osram Chips 110W 5x7 Inch Led Headlights 7x6 Led Sealed Beam Headlamp with High Low Beam H6054 6054 Led Headlight Replacement for Jeep YJ Cherokee XJ H5054 H6054LL 6052 6053 2 Pcs
Sold by: Afex
$85.99

I couldnt find anything for a Corvette application.... Only Jeep!! Is the connection the same for our cars?

[ram_g]

This is exactly what I used in my car - they work great and are a huge improvement over the stock lighting pattern/output. I have no regrets whatsoever.

However, be aware of the following:
- The stock sheet metal buckets need to be slightly modified to allow these to fit. Specifically, there is a small "bump" on one side of each bucket, that needs to be trimmed away for these to fit. I used a Dremel tool with a cutting disk and simply cut off the sheet metal in that area. That worked fine and there is plenty of material around the cut to provide strength.
- You will need to modify the foglamp wiring to ensure that the foglamps work. I was not able to make load resistors work with these LEDs. I did the "Yun mod" on the foglamp relay and that worked out perfectly.
- The LED units are quite a bit heavier than the stock plastic headlamps. My headlamp motors (specifically the plastic pellets inside) were already on their last legs and pretty much gave up after I made this mod. Replaced the pellets and all is well again.

Finally, be aware that this unit is available in a black background (as pictured) and also in chrome. I chose chrome as I think it looks better / closer to stock. YMMV.

[Ccmano]

Originally Posted by ram_g

This is exactly what I used in my car - they work great and are a huge improvement over the stock lighting pattern/output. I have no regrets whatsoever.

However, be aware of the following:
- The stock sheet metal buckets need to be slightly modified to allow these to fit. Specifically, there is a small "bump" on one side of each bucket, that needs to be trimmed away for these to fit. I used a Dremel tool with a cutting disk and simply cut off the sheet metal in that area. That worked fine and there is plenty of material around the cut to provide strength.
- You will need to modify the foglamp wiring to ensure that the foglamps work. I was not able to make load resistors work with these LEDs. I did the "Yun mod" on the foglamp relay and that worked out perfectly.
- The LED units are quite a bit heavier than the stock plastic headlamps. My headlamp motors (specifically the plastic pellets inside) were already on their last legs and pretty much gave up after I made this mod. Replaced the pellets and all is well again.

Finally, be aware that this unit is available in a black background (as pictured) and also in chrome. I chose chrome as I think it looks better / closer to stock. YMMV.

Ditto... if you know what that means.

H

[G8nightman]

Originally Posted by ram_g

This is exactly what I used in my car - they work great and are a huge improvement over the stock lighting pattern/output. I have no regrets whatsoever.

However, be aware of the following:
- The stock sheet metal buckets need to be slightly modified to allow these to fit. Specifically, there is a small "bump" on one side of each bucket, that needs to be trimmed away for these to fit. I used a Dremel tool with a cutting disk and simply cut off the sheet metal in that area. That worked fine and there is plenty of material around the cut to provide strength.
- You will need to modify the foglamp wiring to ensure that the foglamps work. I was not able to make load resistors work with these LEDs. I did the "Yun mod" on the foglamp relay and that worked out perfectly.
- The LED units are quite a bit heavier than the stock plastic headlamps. My headlamp motors (specifically the plastic pellets inside) were already on their last legs and pretty much gave up after I made this mod. Replaced the pellets and all is well again.

Finally, be aware that this unit is available in a black background (as pictured) and also in chrome. I chose chrome as I think it looks better / closer to stock. YMMV.

I put them in 3 different cars they fit right in no mods.

[Locobob]

I tried those briefly but wasn't super impressed with the light output. I'm running the Genessi 7x6 and I'm really happy with them, they are closer to $200 for the pair though. And yes the Jeep XJ and Corvette are the same, I own those exact two cars lol

[32valvZ]

Thanks everyone... They'll be here Friday. I hate driving my Z at night.... and the wife forget it... she is white knuckling it the whole ride... I figure for $85.00 they're worth a shot over the yellow stockers.

[mpiecyk]

Robert,
Do you know the model number of the Genessi 7"X6".
Tanks in Advance
Mike P.

[-=Jeff=-]

I have GE Nighthawk LEds for headlights and Beamtech LEDs for Fog lights

[Locobob]

Originally Posted by mpiecyk

Robert,
Do you know the model number of the Genessi 7"X6".
Tanks in Advance
Mike P.

The box says A0102, they are a little difficult to track down, I think I found them on Amazon. I thought I did a write up on them here but perhaps not, I do have a write up with pics on Facebook (Locobobs ZR-1 Page)

[mpiecyk]

Hey Jeff,
Was the installation for the fog lights very difficult?