DIY euro tail lights
 

I have always liked the look of the euro taillights decided to make my own. Attachment 14607


Sent from my iPhone using ZR-1 Net Registry

Re: DIY euro tail lights
 

Now to make a functional housing and wiring

Re: DIY euro tail lights
 

Look good. How did you do that?

Re: DIY euro tail lights
 

Lee,the wiring is easy,the wire you need is already in the harness and stops at the rear bulkhead. I got some OEM connectors, installed a terminal in the open cavity in the plug,made the wiring harness for the lights,done. Here's the sketchy part,when your 3rd brake light circuit goes out at the switch,you have no brake lights. I did mine years ago,can't remember every detail but if you need a hand get in touch.

Re: DIY euro tail lights
 

Thanks! might reach out once I get to that point.


Sent from my iPhone using ZR-1 Net Registry

Re: DIY euro tail lights
 

I tapped into the CHMSL circuit for the rear brake signal.

Re: DIY euro tail lights
 

Those look very nice. Printed? I've got a set of those on my 99' FRC my father installed years ago.

DIY euro tail lights
 

You are the man Lee! That is slicker than oyster snoochie! 🤙🏼


Sent from my iPhone using ZR-1 Net Registry

Re: DIY euro tail lights
 

Attachment 14611


Sent from my iPhone using ZR-1 Net Registry

Re: DIY euro tail lights
 

SWEET! You just saved yourself over $400!!


Sent from my iPhone using ZR-1 Net Registry

Re: DIY euro tail lights
 

x2 -- interested in the process

Re: DIY euro tail lights
 

Let me see if I can get the rest to work.....pointless if I cant make the housing, etc....

Re: DIY euro tail lights
 

The bulb sockets for these are specific to the housing and the part number is AC DELCO LS39 and LS96. The wiring at the brake switch has to be modified but I can't remember how,I'm sure somebody will have the info here.

Re: DIY euro tail lights
 

The brake light signal can be had by tapping into the CHMSL circuit. Much easier than doing it at the brake switch.

Re: DIY euro tail lights
 

If I remember correct you can tap into the 3rd brake light wire to work the brake bulbs, you will also need to cut the white wire coming out of the turn signal connector at the bottom of the steering column to keep from having electrical feed back. I did this euro light conversion 20+ years ago, still have the ZR1.

Re: DIY euro tail lights
 

It's starting to come back to me,I removed,didn't cut the white wire at the switch,wrapped it to isolate it. I believe the light blue wire in the wiring harness is the 3rd brake light for base cars with the light in the bumper,this wire runs all the way to the back of the car an stops at the main connector at the bulkhead. On the opposite side of the harness connector is the empty cavity where you would install a terminal connected to the EURO setup. In my install not a single wire was cut,spliced.

Re: DIY euro tail lights
 

I ran a new wire from the dash to the back for the brake lights. There is a reason for 2 brake light switches. I cut the wire under the dash to by pass the turn signal flashing. but then ran the new wire from to the back of the car..

Since my taillight harness had been messed with prior to me owning I just rebuilt it with the euro sockets and soldered everything

Re: DIY euro tail lights
 

I popped the white wire out of the harness connector. Then ran a wire from the targa hoop down to the back and used scotchlock for connection to harness I built.

Re: DIY euro tail lights
 

Hi guys...
Does anyone have instructions on how to mount the wiring for european tail light?
I know that some years ago ecklers or other site had the scheme...

Re: DIY euro tail lights
 

Attachment 15594

Too hot to be pulling off parts, started making the housing


Sent from my iPhone using ZR-1 Net Registry

Re: DIY euro tail lights
 

Wow, those turned out amazing! :thumbsup: I'm going to do this one of these days. Did you make the red over amber lenses?

Jay

Re: DIY euro tail lights
 

Assuming its going to sit in like the standard lights? The euro housing sits more more flush to the rest or the bumper to have room for the second bulb socket i wonder if you will have space issues on the back side.