ZR-1 Net Registry Forums

ZR-1 Net Registry Forums (http://zr1.net/forum/index.php)
-   C4 ZR-1 Parts For Sale / Wanted (http://zr1.net/forum/forumdisplay.php?f=10)
-   -   Ported Intake (http://zr1.net/forum/showthread.php?t=15116)

LGAFF 07-09-2011 04:17 PM

Ported Intake
 
x

LGAFF 07-09-2011 11:20 PM

Re: Ported Intake
 
x

WVZR-1 07-10-2011 09:16 AM

Re: Ported Intake
 
Quote:

Originally Posted by LGAFF (Post 118457)
I have a fully ported Plenum I/H set ready for go on an exchange basis.


35mm ball passes completely through on primaries.......

IHs are blasted to aluminum and read for paint and PC

Can blast plenum also

$700 plus your INJ Housings and Plenum

Shipping not included

I would think IH casting #'s could be important to prospective buyers.

XfireZ51 07-10-2011 09:22 AM

Re: Ported Intake
 
Quote:

Originally Posted by WVZR-1 (Post 118480)
I would think IH casting #'s could be important to prospective buyers.

Why? Besides, Lee doesn't remove any material from outside the IH and media blasting just cleans up the surface.

LGAFF 07-10-2011 09:33 AM

Re: Ported Intake
 
x

WVZR-1 07-10-2011 10:12 AM

Re: Ported Intake
 
Quote:

Originally Posted by XfireZ51 (Post 118482)
Why? Besides, Lee doesn't remove any material from outside the IH and media blasting just cleans up the surface.

I would guess that if these were '90-'92 MY the primaries were sealed to the injector housings with an o-ring in the IH. Correct? That's just what I recall!

I recall that later injectors could be used and that these seals (that aren't readily available) seldom failed so it's been generally accepted to inspect and use the later injectors removing the lower seal.

I don't know that Jerry has these sealing rings or not.

Were I in the market I would certainly like to know.

I thought it a relevant question. Maybe NOT!

LGAFF 07-10-2011 10:17 AM

Re: Ported Intake
 
x

WVZR-1 07-10-2011 10:26 AM

Re: Ported Intake
 
Quote:

Originally Posted by LGAFF (Post 118494)
Nope, only 0 rings are the fuel injectors.....IHs use normal gaskets.

I checked Jerry's and he has early sealing rings! Perhaps this would be a "GOOD READ"! It seems to me this should answer the WHY!!!!!

https://jerrysgaskets.com/store2/roo...on%20Guide.pdf

Just post the casting information. What's the big deal?

LGAFF 07-10-2011 10:34 AM

Re: Ported Intake
 
x

WVZR-1 07-10-2011 11:11 AM

Re: Ported Intake
 
Quote:

Originally Posted by LGAFF (Post 118494)
Nope, only 0 rings are the fuel injectors.....IHs use normal gaskets.


You see this comment contradicts the '90-'92 MY primary injector application. Right? Did you do the "read" I suggested?

Can early IH's be modified to accept primary o-rings on the injectors? Don't know and have never seen comments relating to it.

Was there interest on my part? Not now!


All times are GMT -4. The time now is 12:26 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright ZR-1 Net Registry 2025