90 oil filter housing- replacing sensors and gasket - any loctite or RTV needed? - ZR-1 Net Registry Forums

Corvette95 · 04-05-2020

I just took the oil filter housing off my 90, I am replacing all the sensors on the housing and installing a new gasket. The sensor all have the factory thread seal on them, is there any hands on advice for supplementing the OE thread sealant on the sensors with a specific loctite or other? Also, is the gasket just contact or should I put any RTV or spray adhesive on it? I am trying to do this once and done so I want to stop any leaks for the future. ALSO, is did tighten the oil pressure regulating valve cover, it was not super loose, but took 1-2 full turns to get tight. I didn't replace the 8mm with 10mm only due to the virus as I can't get out to the stores. Quick advice on the loctite and RTV would be appreciated as it is going back on this morning. THX!

Dynomite · 04-05-2020

I use a bit of permatex (very light coat) on each side of the Oil Filter Adapter gasket and a bit of permatex or Teflon tape on the sensor threads which are tapered pipe threads. A bit of Blue or red Loctite on the oil filter adapter bolts.

19 ft-lbs on the three Oil Filter Adapter 8mm bolts (35mm, 40mm, 45mm) with 10mm heads.

This chart from Jerry's Gaskets (Item 17, 18, 19)

Corvette95 · 04-05-2020

THANKS!

Corvette95 · 04-05-2020

Didn't want to start a new thread but do you know if this bushing/washer on the inlet hose is an available separate part and if so, anyone have a part number or idea where I can get it? Thanks

Dynomite · 04-05-2020

I am not sure if the Heater Coolant Return is what you are talking about .......you best ask Jerry if that piece is included if in fact this is the associated fitting

Heater Coolant Return

Corvette95 · 04-05-2020

Thanks, I already have that piece in transit from Jerry, this is for the other side of the hose, I have the black clip in piece, I need the "slip over" bushing that is in the arrows.

Dynomite · 04-05-2020

Quote:

Originally Posted by Corvette95

Thanks, I already have that piece in transit from Jerry, this is for the other side of the hose, I have the black clip in piece, I need the "slip over" bushing that is in the arrows.

I am confused as that black clip (and I assume "bushing") appears what is part of Jerry's Heater Coolant Return Fitting. Someone else (Jerry) will know for sure.

I guess you are talking about the other "outlet" line???

04-05-2020	#2
Dynomite Join Date: Aug 2009 Location: South Dakota/California Posts: 3,816	Re: 90 oil filter housing- replacing sensors and gasket - any loctite or RTV needed? I use a bit of permatex (very light coat) on each side of the Oil Filter Adapter gasket and a bit of permatex or Teflon tape on the sensor threads which are tapered pipe threads. A bit of Blue or red Loctite on the oil filter adapter bolts. 19 ft-lbs on the three Oil Filter Adapter 8mm bolts (35mm, 40mm, 45mm) with 10mm heads. This chart from Jerry's Gaskets (Item 17, 18, 19) __________________ Clickable links On Iphone Touchable Links -Solutions- LT5 Modifications/Rebuild Tricks Low Mileage ZR-1 Restoration 1990 Corvette (L98) Modifications LT5 Eliminated Systems LT5 Added Systems LT5/ZR-1 Fluids 1995 LT5 SPECIFIC TOP END REBUILD TRICKS Last edited by Dynomite; 04-05-2020 at 02:44 PM.

04-05-2020	#3
Corvette95 Join Date: Jan 2006 Location: Decatur, AL Posts: 1,140	Re: 90 oil filter housing- replacing sensors and gasket - any loctite or RTV needed? THANKS! __________________ Corvette95 Registry and Forum (*************) 1989 C4 Conv Wht/Gry Auto Hardtop Top Flight SOLD 1995 C4 Coupe Purple/Blk 6 Speed 1989 C4 Conv Wht/Red Auto SOLD 1996 C4 Conv Black/Tan Auto SOLD 1994 C4 Coupe Wht/Blk SOLD 1995 C4 ZR-1 White/Gry #278 Dual Dunn Head SOLD 1986 C4 Coupe Black/Red 4+3 SOLD 1990 C4 ZR-1 Red/Red #0454

04-05-2020	#5
Dynomite Join Date: Aug 2009 Location: South Dakota/California Posts: 3,816	Re: 90 oil filter housing- replacing sensors and gasket - any loctite or RTV needed? I am not sure if the Heater Coolant Return is what you are talking about .......you best ask Jerry if that piece is included if in fact this is the associated fitting Heater Coolant Return __________________ Clickable links On Iphone Touchable Links -Solutions- LT5 Modifications/Rebuild Tricks Low Mileage ZR-1 Restoration 1990 Corvette (L98) Modifications LT5 Eliminated Systems LT5 Added Systems LT5/ZR-1 Fluids 1995 LT5 SPECIFIC TOP END REBUILD TRICKS Last edited by Dynomite; 04-05-2020 at 05:14 PM.

04-05-2020	#6
Corvette95 Join Date: Jan 2006 Location: Decatur, AL Posts: 1,140	Re: 90 oil filter housing- replacing sensors and gasket - any loctite or RTV needed? Thanks, I already have that piece in transit from Jerry, this is for the other side of the hose, I have the black clip in piece, I need the "slip over" bushing that is in the arrows. __________________ Corvette95 Registry and Forum (*************) 1989 C4 Conv Wht/Gry Auto Hardtop Top Flight SOLD 1995 C4 Coupe Purple/Blk 6 Speed 1989 C4 Conv Wht/Red Auto SOLD 1996 C4 Conv Black/Tan Auto SOLD 1994 C4 Coupe Wht/Blk SOLD 1995 C4 ZR-1 White/Gry #278 Dual Dunn Head SOLD 1986 C4 Coupe Black/Red 4+3 SOLD 1990 C4 ZR-1 Red/Red #0454