Locobob's Interior Mod Thread - Page 8 - ZR-1 Net Registry Forums

-=Jeff=- · 11-19-2013

LMAO @ mike

that was good

WVZR-1 · 11-20-2013

Quote:

Originally Posted by Locobob

Haven't made any progress for the last week, major dental issue took the wind right out of my sails

Anyhow hope to start working on it again soon.

The head unit has a "reverse" wire that acts as a trigger for the back-up camera when the transmission is placed in reverse. Anyone have experience with this... what is the easiest way to hook it up?

Also is there a convenient ground under the dash somewhere... besides splicing into an existing wire?

You should be able to catch the BU lamp LTGRN at either C209 @ the lower side of the IP on the right OR @ C401 which is at the RH halo I believe in the vicinity of where the CHMSL connection is made from the ABS unit etc. Top of RH seat vicinity.

GOLDCYLON · 11-20-2013

Quote:

Originally Posted by mike100

looks good sans wing, but now I just figured out why you are rocking those louvers. You could say it is for the summer rays in PHX, but i know the real reason now:

Yep no argument

Locobob · 11-20-2013

Quote:

Originally Posted by WVZR-1

You should be able to catch the BU lamp LTGRN at either C209 @ the lower side of the IP on the right OR @ C401 which is at the RH halo I believe in the vicinity of where the CHMSL connection is made from the ABS unit etc. Top of RH seat vicinity.

Ah now that sounds much better than jacking the car and trying to squeeze up to the switch which appears to be near the bell-housing. I'll poke around and see if I can find it. If not then perhaps I will just run another wire along the back-up cam route since I can readily see and access the LT green wire through the license plate hole.

chriskinzel · 11-20-2013

When I installed my back-up camera, I used a extra wire with the camera wire. Hooked it up at the back-up light, behind the license plate. Haven't looked back since. Or have I? I'm confused.

Locobob · 11-21-2013

So I think I have found the easiest route to connect the reverse wire off the head unit to the back-up light circuit. Here it is under the passenger dash, this should be C209 as it matches the connector description in the FSM electrical supplement.

The back-up lamp circuit is a LT green wire, at first I was a little confused since there are two wires here which appear to be LT green but another look at the FSM indicated its terminal F on C209 so it should be the one at the top of the pic.

I probably could have run a wire all the way back to the reverse lamps in less time but by doing this research I found a super close spot to plug in and also learned a lot about the FSM in the process - thanks WVZR-1

Schrade · 11-21-2013

Quote:

Originally Posted by Locobob

So I think I have found the easiest route to connect the reverse wire off the head unit to the back-up light circuit. Here it is under the passenger dash, this should be C209 as it matches the connector description in the FSM electrical supplement.

The back-up lamp circuit is a LT green wire, at first I was a little confused since there are two wires here which appear to be LT green but another look at the FSM indicated its terminal F on C209 so it should be the one at the top of the pic.

I probably could have run a wire all the way back to the reverse lamps in less time but by doing this research I found a super close spot to plug in and also learned a lot about the FSM in the process - thanks WVZR-1

That's good work

Where IS the line tap? Can't actually see it there...

And learning to follow schematics in FSM is good brainwork too. Makes for good systemic and cognitive processes!

Locobob · 11-21-2013

Quote:

Originally Posted by Schrade

That's good work

Where IS the line tap? Can't actually see it there...

And learning to follow schematics in FSM is good brainwork too. Makes for good systemic and cognitive processes!

Its not there yet, probably get that done today.

GOLDCYLON · 11-21-2013

Bob sorry I missed you latest post however if you have a Varible Speed Sensor wire on your head unit the VSS wire is the Forrest Green Wire with the White Stipe off the Bose factory radio harness. Normally you need this wire if you have a NAV unit and dont want to rely on dead reackoning. D

Locobob · 11-21-2013

Quote:

Originally Posted by GOLDCYLON

Bob sorry I missed you latest post however if you have a Varible Speed Sensor wire on your head unit the VSS wire is the Forrest Green Wire with the White Stipe off the Bose factory radio harness. Normally you need this wire if you have a NAV unit and dont want to rely on dead reackoning. D

My head unit does not have NAV, going to do that separately

11-19-2013	#71
-=Jeff=- Join Date: Jul 2007 Location: Bartlett, IL Posts: 7,155	Re: Locobob's Interior Mod Thread LMAO @ mike that was good __________________ 1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Custom Interior NCM Lifetime Member #978

11-20-2013	#75
chriskinzel Join Date: Nov 2011 Location: Salt Lake City, Utah Posts: 169	Re: Locobob's Interior Mod Thread When I installed my back-up camera, I used a extra wire with the camera wire. Hooked it up at the back-up light, behind the license plate. Haven't looked back since. Or have I? I'm confused. __________________ 91 ZR-1 Red on Red #922

11-21-2013	#76
Locobob Join Date: Jan 2004 Location: Portland, OR Posts: 1,057	Re: Locobob's Interior Mod Thread So I think I have found the easiest route to connect the reverse wire off the head unit to the back-up light circuit. Here it is under the passenger dash, this should be C209 as it matches the connector description in the FSM electrical supplement. The back-up lamp circuit is a LT green wire, at first I was a little confused since there are two wires here which appear to be LT green but another look at the FSM indicated its terminal F on C209 so it should be the one at the top of the pic. I probably could have run a wire all the way back to the reverse lamps in less time but by doing this research I found a super close spot to plug in and also learned a lot about the FSM in the process - thanks WVZR-1 __________________ Robert ZR-1 Net Registry Oregon State Director 91 ZR-1 #431 Black/Black LPE 368

11-21-2013	#79
GOLDCYLON Join Date: May 2007 Location: Peoria, AZ Posts: 9,154	Re: Locobob's Interior Mod Thread Bob sorry I missed you latest post however if you have a Varible Speed Sensor wire on your head unit the VSS wire is the Forrest Green Wire with the White Stipe off the Bose factory radio harness. Normally you need this wire if you have a NAV unit and dont want to rely on dead reackoning. D __________________ GOLDCYLON - 91 ZR-1 #2014 GOLDCYLON - 90 ZR-1 #2794, 4L60e (Formerly Schrade's) GOLDCYLON - 11 CTS-V Arizona State Director 91 WHITE/BLACK #2014. 380 P&P&PCed,Ported Heads, Jeal Long tubes, Corsa Exhaust/FIKSE FM-5s /LED TLs, LED Headlights, Front Wilwood 6 piston narrowlite calipers and rear Wilwood caliper street shop mod,CNCed Coolant Pipes,TPI Cvr,Filter cover,Stainless Bolts, DRM/DOM PROM /ZFDOC mod build #102,DRLs,BMAD with stainless Debris Screen,Coplan Air Blaster, Pioneer APP Radio 4,Brey-Krause HB,Sub Bar,Fire extinguisher seat mount,DRM Coilovers,LEDs everywhere,Compass mirror (orange),V1 DIC hidden display, Homelink sun visor, Carbon Fiber top x3 and APSIS Carbon Fiber interior, APSIS CF Steering Wheel/NAPA Leather, Banski trailing arms, Guldstrand front suspension,urethane bushings from Prothane (total suspension) ZFDoc drive shaft safety loop, raptor shift light (orange),AO engineering louver front plate, Console seat cushion, 96CE seats with black custom Sheepskins, ss billet catch can,Viper remote entry/alarm,Cragar Rear Louvers,LED side louver lights, Dewitts Radiator with SPAL fans and a Woods 160 T-Stat 90 RED/BLACK #2794. 4L60e Automatic Stage V by RPM Transmission, TCI Dedicated TCM, OBX Stainless Headers, Corsa Exhaust, SAN Secondaries and Haibeck PROM, Exotic Muscle Coil overs, LED Interior Lights, LED Tail Lights, LED Headlights, 94 Sport seats with black custom Sheepskins , Cragar rear louvers, GS Front calipers, Banski Trailing arms, APSIS Carbon Fiber steering wheel, Front and Rear Baer Eradispeeds, DRLs, Guldstrand front suspension,urethane bushings from Prothane (total suspension), Dewitt's Raditor with Dual SPAL fans and a Haibeck 170 T-Stat 11 RED/GREY CTS-V