|
05-09-2012
|
#11 |
|
Join Date: Jun 2010
Location: back in lone pine
Posts: 591
|
Re: First Plenum Pull - Code 16
anyone have any luck straightening a pin that's been bent flat .if so how did you straighten it out ?????
|
|
|
|
05-09-2012
|
#12 |
 
Join Date: Dec 2004
Location: Jacksonville, FL USA
Posts: 4,645
|
Re: First Plenum Pull - Code 16
 I fixed mine using a very small needle nose. I was gentle as those pins don't look like they tolerate a lot of bending. I bent my pin fairly flat also, kind of into an "L" shape. Just be gentle, and it shouldn't break off. fwiw, so I never do that again, I marked the "top" side of the connector using a red sharpie. Tom
__________________
1990 ZR-1, Black/grey, #2233, stock. ZR-1 Net Reg Founding Member #316 & NCM member |
|
|
|
|
10-13-2012
|
#13 |
Join Date: Jul 2007
Location: Anchorage, AK
Posts: 106
|
Re: First Plenum Pull - Code 16
To all who responded:
This turned out to be a bent pin on the ignition module. It was easily straightened and the car jumped to life, no codes no problems. Repair was postponed due to an A-Fib(cardiac episode) issue, mine not the car  , it has been surgically corrected and all is well there as well. Sorry for the delayed resolution.I'll post about a fuel pressure problem that developed 2,599 miles after I first drove it out of the garage under another title. Rich
__________________
REBelZ '92 ZR-1 Yellow/Black #031 |
|
|
|
|
10-13-2012
|
#14 |
 
Join Date: Jan 2009
Location: Portland Oregon metro area (Washington side)
Posts: 3,207
|
Re: First Plenum Pull - Code 16
Sure glad to see you back.
All other things just pale to being back in the saddle. Life begins at 180mph !
__________________
Scott  Vett owner since 1979._It's about the car and the people |
|
|
|
|
10-13-2012
|
#15 | |
 
Join Date: Aug 2005
Location: Northridge, CA
Posts: 1,445
|
Re: First Plenum Pull - Code 16
Quote:
a car can. Well, almost..... |
|
|
|
|
|
10-14-2012
|
#16 |
 
Join Date: Dec 2005
Posts: 692
|
Re: First Plenum Pull - Code 16
Number one reason I like this place.... owners helping owners :-)
Number two.....Corvette babes ;-) |
|
|
|
|
10-15-2012
|
#17 |
|
Join Date: Dec 2004
Location: Jacksonville, FL USA
Posts: 4,645
|
Re: First Plenum Pull - Code 16
Holy Cow Rich! I'm glad to hear that the cardiac condition is resolved.
Be Well Brother!
__________________
1990 ZR-1, Black/grey, #2233, stock. ZR-1 Net Reg Founding Member #316 & NCM member |
|
|
|
|
10-16-2012
|
#18 | |
|
Join Date: Jul 2007
Location: Anchorage, AK
Posts: 106
|
Re: First Plenum Pull - Code 16
Quote:
I've had A-Fib issues since 2003, It's a pretty common issue. After the 4th Zap to put it back into rhythm since then, when it went out again just 4 month later, I decided to have the Ablation surgery. The heart center has just started using Cryoablation. It was scary, they are messin' with your heart... All went as planed. I almost had a heart attack though(kidding) when I got the hospital bill. For the Prep, Operating room and one night in a semi-private progressive care room, just the hospital charges were $105,650.00... My insurance paid every dime!! Interestingly enough, they wouldn't pay $629.00 of the surgeons $2,500.00 bill. Go figure! Rich "Rebel" Ballou
__________________
REBelZ '92 ZR-1 Yellow/Black #031 Last edited by rebelz; 10-16-2012 at 01:16 AM. Reason: Spelling errors - Damnit Jim I'm an engineer not a dictionary! |
|
|
|
|
|
10-16-2012
|
#19 | |
Join Date: Oct 2004
Location: Folsom CA
Posts: 1,646
|
Re: First Plenum Pull - Code 16
Quote:
;-) My vote is on the DIS plug as well. Nearly impossible to get to without pulling the plenum again, but if this is the first time you've seen this code, it is the smoking gun. 'Crabs
__________________
TomC '90ZR1 #792 Honorary Pirate [B]If it ain't FUN, you're doing something terribly WRONG. [/B] |
|
|
|
|
|
10-18-2012
|
#20 | |
|
Join Date: Jul 2007
Location: Anchorage, AK
Posts: 106
|
Re: First Plenum Pull - Code 16
Quote:
Rich
__________________
REBelZ '92 ZR-1 Yellow/Black #031 |
|
|
|
|
 |
|
|
Linear Mode
